Custom Sewing Solutions for Knit and Woven Programs

Quick answer: Custom sewing is specified, not inherited: stitch type and density, seam construction, needle size and thread programme are decisions. Knit routes use linking and overlock with elastic seams; woven routes use lockstitch and specialised machines for collars, cuffs and plackets.

Custom sewing is the difference between a factory that assembles and a factory that builds to spec. Stitch types, seam construction, needle gauges and thread programmes are all specified decisions — and on a mixed knit-woven floor, they are decided differently for each route. This guide covers what buyers should specify, what changes between knit and woven lines, and where sewing quality is actually won.

Cogarm runs custom sewing across both routes: linking and overlock lines for knitwear, cut-and-sew lines for woven garments, with promotional programs (100 pcs per design MOQ) sharing the same QC standard as bulk production (AQL 2.5).

What to specify before sewing starts

The tech pack should fix four sewing variables; anything left open is a default the factory chooses for you:

  • Stitch types — reference classes (lockstitch, overlock, coverstitch, chainstitch) per seam, not a blanket “normal stitching”
  • Stitch density — stitches per inch or cm per seam class; density drives both appearance and seam strength
  • Thread programme — fibre, ticket number, and whether thread must match body or contrast
  • Seam finishes — which raw edges get bound, overlocked or left clean-finished by garment zone

The cut-and-sew route’s specific expectations — markers, allowances, operation breakdowns — are laid out in the cut and sew technical guide.

Knit versus woven sewing logic

Knits stretch, so seams must too: linking for shaped panels, stretch-capable stitch classes at stress points, and tension tuned so seams do not crack when the fabric gives. Wovens do not stretch, so the logic inverts: stability matters, seam allowances are engineered, and pressing enters the process as a forming step. Managing both logics under one roof changes line planning, staffing and QC sampling — the operational split is covered in the knit vs woven lines management guide.

Where sewing quality is won

Sewing defects are rarely machine failures; they are setup failures. Inline checks at the start of each bundle — tension, density, seam appearance against the sealed sample — catch drift before a full lot repeats it. End-of-line inspection under AQL 2.5 then verifies the lot, with defect classification distinguishing critical (broken stitches on load-bearing seams) from major and minor. Buyers auditing a prospective factory should ask to see inline records, not just final inspection reports.

Small-lot custom sewing

Low-MOQ programs change the economics, not the standard: 100-piece runs cannot amortize engineering time the way 5,000-piece runs do, so the tech pack carries more of the load. The more complete the specification, the less a small lot depends on line-supervisor judgment. The mode-level tradeoffs — OEM supply versus ODM development — sit in the OEM clothing manufacturer guide.

FAQ

Can one factory sew both knits and wovens to the same standard?

Yes, but the two routes need different machines, different operator skills and separate QC reference points. Ask how the floor separates them; a shared undifferentiated line is a red flag.

What stitch density should I specify?

It depends on fabric weight and seam function — there is no universal number. Ask for the factory’s standard per seam class as a starting proposal, then approve or adjust against the sealed sample.

Why does my low-MOQ program cost more per piece to sew?

Setup time — engineering, bundling, machine changeover — is fixed per style. On a 100-piece run it lands on far fewer pieces, which is why complete tech packs matter more at small scale.

How is sewing quality inspected?

Inline checks per bundle plus AQL 2.5 lot inspection against the sealed PP sample. Seam defects are classified critical, major or minor, with a written remedy policy for failed lots.

What should a buyer specify before custom sewing starts?

Specify the stitch package before the line starts. State stitch type and density per centimetre, seam allowance and seam construction, needle size and point type for the fabric, and the thread programme including colour and fibre. Knit routes need elastic seams that survive extension, so linking and overlock dominate; woven routes need lockstitch and dedicated collar, cuff and placket machines. Fix points of measure with a 0.5 cm tolerance, fabric weight per ASTM D3776, OEKO-TEX STANDARD 100 limit values on the finished article, and acceptance as AQL 2.5 under ISO 2859-1.

Cogarm has manufactured custom knitwear and woven garments in Dongguan, Guangdong, China since 2006. Minimum order is 100 units per style and colourway.

About the Author

Leave a Reply