Quick answer: Prototyping has three sample types: a fit sample that proves the block, a pre-production sample on bulk yarn or fabric, and a size set that proves grading. Two approval loops are normal; a third is a warning that the spec is still moving.
Garment prototyping is where a tech pack stops being a PDF and becomes a garment you can hold, fit and argue about. Done well, it absorbs every ambiguity in the spec before bulk knitting or cutting starts. Done badly, it produces a sample nobody approved and a bulk lot full of surprises. This guide walks the prototype stage for knit and woven programs and shows what a buyer should test on each sample type.
Cogarm prototypes custom knitwear and woven garments across the same lines that run bulk — gauge 3GG–18GG flat-bed knitting for knits, dedicated woven cutting lines for wovens — so the prototype reflects real production conditions, not a sample room shortcut.
Sample types and what they decide
A program usually passes through three physical samples, each answering a different question:
- Proto sample — proves the design is buildable: silhouette, construction, stitch or seam types. Materials may be substituted; fit is approximate.
- Fit sample — proves the size chart works on a body. Grade rules are tested here, not in bulk.
- PP (pre-production) sample — proves the production spec: correct yarn or fabric lot, colour, wash finish, measurements. This becomes the physical reference bulk inspection is anchored to.
Collapsing the three into one “quick sample” is the most common shortcut buyers regret. The gate discipline around the last one is detailed in the pre-production samples guide.
How knit and woven prototypes differ
Knit prototyping is programming: the proto is knitted on computerized flat-bed machines from a program file, so a gauge or construction question can be answered with a re-program, not a re-cut. Woven prototyping is cutting and sewing: every change costs a new marker, so revisions are cheaper to batch. The structural difference between the two routes — shaped panels versus cut pieces — is compared in the fully fashioned vs cut and sew guide, and it directly changes how many proto rounds a program needs.
Lead times and approval loops
Prototyping runs 10–15 days per round from a complete tech pack. Sourced specialty yarns — a specific merino micron, a GRS-certified blend — add 5–7 days because the yarn procurement enters the critical path. The calendar risk is rarely the sample itself; it is the approval loop around it. Comments that arrive in three separate emails over two weeks cost more days than the knitting did. Buyers who ship on time send consolidated, prioritized comments within a fixed window.
What to check on a prototype
- Measurements against the size chart at five or more points, not just chest and length
- Gauge and hand feel against the approved yarn, especially after wash
- Colour under standardized lighting, quoted as Pantone TCX ±1 shade tolerance
- Construction details: linking seams on knits, stitch density, trims and labels placement
- Wash finish: the sample should carry the bulk wash recipe, not a placeholder
A structured checklist for the inspection side — what gets measured, how defects are classified — carries into bulk in the sweater quality control checklist.
FAQ
How many prototype rounds does a custom garment need?
One proto and one PP sample is normal for a complete tech pack; a fit sample sits between them for size-chart programs. Multiple proto rounds usually mean the tech pack was incomplete — fixing the pack is cheaper than re-sampling.
Can I skip the proto and go straight to a PP sample?
Only if the construction is a repeat of a previous program. New silhouettes hide their mistakes at the proto stage; skipping it moves discovery into bulk, where changes cost the most.
Why does sourced yarn add 5–7 days to sampling?
Stock yarn supports immediate sampling; a buyer-specified yarn — micron, spin, certification — must be procured, MOQ permitting, before the first stitch can be knitted.
Who owns the approved sample?
The PP sample is sealed: one copy stays with the factory QC line as the bulk inspection reference, one goes to the buyer. Both sides must reference the same sealed sample in any dispute.
Which sample types should a buyer approve before bulk production?
Approve three things, in order. The fit sample proves the block and the silhouette; it can be made in a stock yarn because it is not a shrinkage test. The pre-production sample must run on bulk yarn or bulk fabric, with the final trims, because this is where shrinkage and hand-feel are decided. The size set proves grading across the range. Record every point of measure with a 0.5 cm tolerance, fabric weight per ASTM D3776, colour against a Pantone TCX chip, OEKO-TEX STANDARD 100 limit values on the finished article, and AQL 2.5 under ISO 2859-1.
Cogarm has manufactured custom knitwear and woven garments in Dongguan, Guangdong, China since 2006. Minimum order is 100 units per style and colourway.
